# Travel limits after homing (units are in mm)
>X_MIN_POS 0
>Y_MIN_POS 0
>Z_MIN_POS 0
>X_MAX_POS 100
>Y_MAX_POS 100
>Z_MAX_POS 100

# position of hotend  for filament change and pause print
>FILAMENT_CHANGE_X_POS 5	 # X position of hotend  for filament change and pause print
>FILAMENT_CHANGE_Y_POS 5	 # Y position of hotend  for filament change and pause print
>FILAMENT_CHANGE_Z_ADD 5	 # Z addition of hotend (lift)	for filament change and pause print 

#============================== Stepper Motor Settings ============================

#Set stepper current 
>CURRENT_VREF_XY                700	#Default motor current for XY in mA£¬range (0~1000)
>CURRENT_VREF_Z                 800	#Default motor current for Z  in mA£¬range (0~1000)
>CURRENT_VREF_E                 800     #Default motor current for E  in mA£¬range (0~1000)

#Invert the stepper direction.
>INVERT_X_DIR 	                1	
>INVERT_Y_DIR 	                1
>INVERT_Z_DIR                	1
>INVERT_E0_DIR           	1

#Movement setting
>DEFAULT_X_STEPS_PER_UNIT	606	#Default Axis-X Steps Per Unit (steps/mm)	
>DEFAULT_Y_STEPS_PER_UNIT	606	#Default Axis-Y Steps Per Unit (steps/mm)	
>DEFAULT_Z_STEPS_PER_UNIT	600	#Default Axis-Z Steps Per Unit (steps/mm)	
>DEFAULT_E_STEPS_PER_UNIT	1040	#Default Axis-E Steps Per Unit (steps/mm)	

>DEFAULT_X_MAX_FEEDRATE		20	#Default Axis-X Max Feed Rate (mm/s)		
>DEFAULT_Y_MAX_FEEDRATE		20	#Default Axis-Y Max Feed Rate (mm/s)		
>DEFAULT_Z_MAX_FEEDRATE		20	#Default Axis-Z Max Feed Rate (mm/s)		
>DEFAULT_E_MAX_FEEDRATE		20	#Default Axis-E Max Feed Rate (mm/s)		

>DEFAULT_X_MAX_ACCELERATION	50	#Default Axis-X Max Acceleration (change/s) change = mm/s
>DEFAULT_Y_MAX_ACCELERATION	50	#Default Axis-Y Max Acceleration (change/s) change = mm/s
>DEFAULT_Z_MAX_ACCELERATION	50	#Default Axis-Z Max Acceleration (change/s) change = mm/s
>DEFAULT_E_MAX_ACCELERATION	100	#Default Axis-E Max Acceleration (change/s) change = mm/s

>
>DEFAULT_XJERK 			2	#Default Axis-X Jerk (mm/s)	
>DEFAULT_YJERK 			2	#Default Axis-Y Jerk (mm/s)	
>DEFAULT_ZJERK 			0.4	#Default Axis-Z Jerk (mm/s)	
>DEFAULT_EJERK 			0.5	#Default Axis-E Jerk (mm/s)	

>DEFAULT_ACCELERATION		1000      	#Default Acceleration
>DEFAULT_RETRACT_ACCELERATION	1000	#Default Retract Acceleration
>DEFAULT_TRAVEL_ACCELERATION	1000	#Default Travel Acceleration

#============================= Thermal Settings ============================

>EXTRUDE_MINTEMP 	170
>HEATER_0_MAXTEMP 	275


#======================== Thermal Runaway Protection =======================

>THERMAL_PROTECTION_PERIOD 		40    	#Seconds      ´̣Ó¡ÖĐ¼́²â
>THERMAL_PROTECTION_HYSTERESIS 		4     	#Degrees Celsius
>WATCH_TEMP_PERIOD 			20	#Seconds      ¼ÓÈȼ́²â
>WATCH_TEMP_INCREASE 			2	#Degrees Celsius


# Type of heat manager for extruder.
>PIDTEMP			1	# 1:PID	; 0:bang-bang
>DEFAULT_Kp			22.2	#	--default
>DEFAULT_Ki			1.08	#	--default
>DEFAULT_Kd			114	#	--default


#==============================  Home Settings ==============================

>X_HOME_DIR -1				# Direction of endstops when homing; 1=MAX, -1=MIN :[-1,1]
>Y_HOME_DIR 1				# Direction of endstops when homing; 1=MAX, -1=MIN :[-1,1]
>Z_HOME_DIR -1				# Direction of endstops when homing; 1=MAX, -1=MIN :[-1,1]
>HOMING_FEEDRATE_XY 1800                # Homing X Y speeds (mm/m)
>HOMING_FEEDRATE_Z  1800                 # Homing Z speeds (mm/m)


#end.